This page for the ballscrew version is under construction, You can download the correct plates from the link below. please come back later for the correct BOM list. You can use the parts below to build a ballscrew version but it also include screw for the other versions.
The Raw Creative 2.5 bill of materials includes recommended parts from AliExpress. The goal is to make the build easier by giving you a clear list of components that fit the machine and work well together.
Some links are affiliate links, which means I may receive a small commission if you purchase through them. This does not increase the price for you.
By using these links, you help support the continued development of Raw Creative 2.5, including videos, build guides, drawings and future improvements.
You are free to source the parts from other suppliers, but the listed components are selected to reduce guesswork and make the build as smooth as possible.
To make the build even easier, selected hardware kits, plates and other custom parts are also available directly from our website. These parts are designed specifically for the Raw Creative 2.5 build and can save time compared to sourcing or making everything yourself.
We update this BOM list regularly, but product links, prices, specifications and availability may change.
Always double-check the product dimensions, quantity and compatibility before ordering. We cannot take responsibility for incorrect purchases, changed listings, unavailable products or supplier mistakes.
All measurements in this BOM list are in millimetres.
The Raw Creative 2.5 is designed around metric components, drawings and hardware. Please make sure that all parts you order match the metric dimensions shown in the list.
If you normally work in inches, do not convert the machine design to imperial measurements unless you fully understand how it affects the build. Mixing metric and imperial parts may cause alignment issues or parts that do not fit correctly.
If you are unsure about sourcing the correct metric hardware, you can purchase the hardware kit from us. The hardware kit includes the required metric screws and selected hardware needed for the build.
Plates
Laser cut steel plates can be expensive to produce in small quantities, especially because every hole and cut adds to the cost. To keep the build cost as low as possible, the plate list is divided depending on which version of the Raw Creative 2.5 you want to build. This way you only need to order the plates required for your machine version. If you want maximum flexibility, a universal plate kit with the required plates for different machine versions is available from our website.
You can buy the plates from us or cut them yourself from 6mm and 3mm steel. Download the plates from here: (only belt version for now) Download plates
Aluminium, Racks, cable and guide rail Calculator
To calculate the length of these parts you can go to our online calculator, klick the link and it will open a separat window. https://creative.rawcnc.com/calculator-for-raw-creative-2-5-machine/ Use the calculator to enter your desired machine size and write down the required measurements for the listed parts. Then come back to this BOM list and use those measurements when ordering your components.
Square tube
If you want to reinforce the X-axis with a steel tube (recomended), you will find them at your local hardware store or online. In Sweden you can buy dem here: Montano or Maskindelen. Choose a tube withe measure 80x40x2mm. Length:
– 935x1000mm machine= 730mm
– 1180×1000-1180x1500mm machine= 970mm
– 1500x2000mm machine= 1300mm (You can use 2x tubes and splice them or a 1000mm tube with gaps on left and right side.)
Reference products
Some products, such as screws, washers and nuts, may link to our Swedish website so you can see what the product looks like and identify the correct type. Please note that these items cannot be purchased individually from that page. They are only shown as a reference and may be included in one of our hardware kits.
The BOM list is based on a larger 2000 x 1500 mm machine to make sure the listed parts are sufficient for most builds. This means that you may have some parts left over if you build a smaller machine. If you want to calculate the quantities more precisely, we recommend studying the build videos and adjusting the quantities according to your own machine size.
We choose hexagon screw due to its color and low price (torx screw or any screw with a low head is used in tight spaces and are marked “Torx”)
Products in the BOM list marked with * are included in our hardware kit.
Use the calculator first to see what length you need for some of the products!
All links open in a new tab or window.
- -Aluminium profiles can be ordered pre-cut from online suppliers or from our Mechanical Parts Kit
- -Guiderail HGR15 can be found here: HGR15 guide rail
- -Cable for steppermotor can be found here: 4-lead Square 0.75mm
- -Ballscrew 1210 can be found here: Ballscrew 1204-1210 (Can be purchased longer and cut to length using a KFL001 bearing.)
- -Timingbelt can be found here: HTD5M timing belt
- -HTD5M timing belt pulley can be found here: D5M timing belt pulley
- 6x M8x35mm (Torx)*
- 6x M8xLock Nut*
- 12x M8x25mm washer*
- 18x M8x16mm Washer*
- 40x M6x16mm *
- 2x M6 Washer *
- 2x M5x6mm*
- 40x M5x8mm*
- 22x M5x12mm*
- 6x M5x12mm (Torx)*
- 8x M5x14mm*
- 10x M5x16mm*
- 4x M5x16mm (Torx)*
- 6x M5x40mm Countersunk screw
- 2x M5x20mm*
- 6x M5x40mm Countersunk screw
- 18x M5x50mm*
- 4x M5x55mm*
- 1x M5x65mm*
- 65x M5 T-nut ball *
- 81x M5 Nut*
- 6x M5 Lock nut*
- 14x M5 Washer 10mm*
- 12x M4x8mm*
- 2x M4x10mm*
- 74x M4x12mm*
- 6x M4x14mm*
- 8x M4x20mm*
- 16x M4x22mm*
- 4x M4x25mm* (if you choose regular motor spacer for Z-motor)
- 4x M4x25mm Countersunk screw* (if you choose the covered motor spacer for Z-motor)
- 58x M4 T-nut Twist type*
- 14x M4 Lock nut*
- 4x Z-axis spacer 40mm*
- 1x Alternative z-axis spacer
- 6x Hole plate 2 holes 20x40mm*
- 1x Screw terminals 8P* (or solder your cables)
- 2x Self tap screw 13mm*
- 19x Self tap screw 25mm*
- 20x Self tapping screw 32mm*
- 8?x Steel angle * Calculate 2 steel angle brackets per support profile.
- 1x Steel angle * (for cable chain)
- 18x Spacers 35mm* (or buy our covered plates)
- 12x HGH15CA Linear bearing blocks
- 2x 280mm HGR15 rail for Z-axis (you can buy longer and cut them)
- 2x 20x20x165mm Aluminium profile*
- 1x 20x40x115mm Aluminium profile* (under the z-axis)
- 8x Small aluminum bracket*
- 2x Z-axis distance 10mm (Included in the plate product or make yourself)
- 1x Ball screw block FK10
- 1x Ball screw nut housing DSG12H
- 1x Ballscrew SFS1210 – 280mm, you can buy longer and cut
- 1x Coupling 8×6.35mm*
- 1x Lock bearing KP001 12mm
- 1x Endcaps 20×60 for aluminiumprofile
- 1x Rail alignment jig set*
- 1x Front and rear aluminium profile covers set
- 1x Raw Creative 2.5 decal set*
- 12x Ball bearing 22mm*
- 2x LED Light 24 volt
- 4x Inductive proximity sensors LJ12A3-4-Z/BX with 3 wires
- 1x Probe socket, banana plug socket*
- 4x Nema 23 steppermotors 8mm or 6.35mm shaft (We use 6.35mm in the video)
- 10x Zip ties*
- 6x 20×40 Aluminium bracket*
- 1x Slotcovers (optional, choose this type or buy our valchromat covers)
- 4x Cable chain 20×50 (max 20mm outer hight for belt and ballscrew, rack can have any size) (machine Lengt + 50cm, machine wdith +50cm)
- 2m Cable sleeve (optional but looks good)
- 5x 4-P plug (buy both plug and socket)
- 1x 2-P plug (buy both plug and socket)
These items are not necessarily included in the BOM list, but they are useful to have during the build.
- Crimp terminals and crimping tool
- Cable spiral / cable wrap
- Heat shrink tubing
- Soldering iron and solder
- Wire stripper
- Side cutters
- Multimeter
- Drill machine
- Drill bits for metal
- Countersink bit
- M5, M6 and M8 taps
- Tap handle
- Measuring tape
- Caliper
- Square / engineer’s square
- Clamps
- Marker pen
- Threadlocker
- Small file or deburring tool
- Basic hand tools
- Metric Allen key set
- Metric spanner / wrench set
- Screwdrivers
- Spirit level or straight edge
Optional but useful:
- Step drill bit
- Cable labels
- Ferrules for electrical wiring
- Ferrule crimping tool
- Zip ties
- Vacuum cleaner or dust extraction during assembly
- Small bench vise
- Workbench or flat assembly table
Threading Taps for aluminium profiles 6mm
It is important that you buy good quality taps. Cheap taps will snap off immediately and if the tap gets stuck in the hole, it cannot be removed.
Note that some profiles have 4mm holes instead of 5mm. If you have such a profile. drill the holes to 5mm and thread with 6mm tap as the picture above.
Other things that may be needed are
- A 1.5 spindle with a frequency converter and 65mm spindle clamp. Alternatively, you can mount on a regular compact router from Makita, Bosch or Dewalt. However, edge trimmers and 1.5kw spindles have a 65mm shaft, so you need a spindle clamp 65mm diameter.
- Consumption table. Cut your own consumable table by following our guides.
- Dust shoe These effectively remove dust and shavings so you don’t inhale it.
If you have the products mentioned above, you are ready to build a Raw Creative machine.
